The first thine which you should know in building electrical circuits for an electrical device are basic theories in electronics. Know the different components used and how to connect them properly to each other. Then study how to read and make schematic diagrams which are graphical representations of an electrical circuit using symbols and images.
Doing so is important when you like to make a particular device but still confused on some parts of this process. This may be something a bit advance for you like the voltage divider which the output produced is a portion only of its input. Before tackling that, learn first or review the basic theories in electronics to better understand the advance stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
When current pass through components, they create resistance to ground from positive voltage and if these are directly connected, this would cause the circuit to be shorted. This direct connection would result in fire, breaking, overheating or explosion which you must avoid. Putting switch would not provide additional resistance so other parts must be added.
There are two ways to wire things together which are classified as parallel and series with the latter indicating all components are being wired one after the other. Meanwhile, the latter indicates the parts are being wired next with each other and that makes electricity to pass them simultaneously. Using both ways when building circuits is possible.
Adding resistance into circuits is done with resistors and they reduce current flow and are also available in a variety of values measured with ohms. They have wattage ratings also and their value is indicated by colored bands around their body. You could learn reading these bands or look up for graphs that helps in calculating their values.
Components which stores electricity and discharges them when they drop are called capacitors and is measured with Farads commonly shown in units of nanofarad, picofarad and microfarad. The types of capacitors commonly used are electrolytic and ceramic disc. The latter being non polarized while the former is polarized requiring one leg to connect properly with either the ground or power.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
Doing so is important when you like to make a particular device but still confused on some parts of this process. This may be something a bit advance for you like the voltage divider which the output produced is a portion only of its input. Before tackling that, learn first or review the basic theories in electronics to better understand the advance stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
A closed circuit is when the electric current is allowed to pass through a path from power source to ground which normally indicates a device is functioning. While an open one breaks this path and will prevent the movement just like in turning off a machine. This is done with a switch so you could alternate between them instead of removing the source.
When current pass through components, they create resistance to ground from positive voltage and if these are directly connected, this would cause the circuit to be shorted. This direct connection would result in fire, breaking, overheating or explosion which you must avoid. Putting switch would not provide additional resistance so other parts must be added.
There are two ways to wire things together which are classified as parallel and series with the latter indicating all components are being wired one after the other. Meanwhile, the latter indicates the parts are being wired next with each other and that makes electricity to pass them simultaneously. Using both ways when building circuits is possible.
Adding resistance into circuits is done with resistors and they reduce current flow and are also available in a variety of values measured with ohms. They have wattage ratings also and their value is indicated by colored bands around their body. You could learn reading these bands or look up for graphs that helps in calculating their values.
Components which stores electricity and discharges them when they drop are called capacitors and is measured with Farads commonly shown in units of nanofarad, picofarad and microfarad. The types of capacitors commonly used are electrolytic and ceramic disc. The latter being non polarized while the former is polarized requiring one leg to connect properly with either the ground or power.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment